Wednesday, February 23, 2011

Chipboards from Scratch
 February 23, 2011
Recycled Crafts
by Wendy Switzer




Supplies:

·         Chipboard
·         Cereal Box or thinner chipboard
·         Paper cutter & paper edge punches
·         Bone folder
·         Ruler
·         Mod Podge
·         Binding clips or another strong clamp
·         Paint brushes
·         Decorative paper/cardstock
·         Embellishments - ribbon, brads, etc. 
·         Emery board
·         Sand paper
·          


Instructions:
 
1.    Cut 10 pieces of chipboard to the size of chipboard pages you desire.
2.    Cut a piece of thinner paper (copy paper) to the height of your book X ½”.
3.    Next gather the chipboard pages together and tap them lightly onto a hard surface to insure that they are all even on the edge you would like to bind together.
4.    Next attach 2 binder clips to secure that pages in place while you work on the next few steps. 
5.    Use a paintbrush to apply a generous amount of ModPodge to the edge that will be your binding.  Be sure to keep the ModPodge on the binding edge ONLY and wipe any excess off of the sides and ends of the book.  Apply another binder clip to the center, but leave plenty of room between the clip top and the binding edge.  Let dry completely and remove the middle clip.
6.    Next, apply another light coat of ModPodge and place add the copy paper piece that you cut in step 2 on the binding edge while the ModPodge is still wet.  Smooth down with a bone folder or by rubbing against the table/counter top. Replace the middle clip and again, let dry completely.
7.    Cut your cereal box into the size you will need to completely cover the book.  Ideally this should be all one piece, but can be broken into two pieces for larger sized books.  Remember to account for the front of the book, the back AND the spine (1/2”)
8.    Once you have your cereal box cut, sand down the “picture” side of the box so that it no longer has a shine to it.  This will help the ModPodge adhere properly.
9.    Take the cereal box piece and measure in the width of your book and score.  Flip the piece around and do the same from the other side.  Crease both score lines to create two folds. 
10. Next from ONE of the fold lines, score another line ½” away from the fold.
11. Next apply ModPodge to the cereal box piece and secure it to your chipboard pages. NOTE…DO NOT add ModPodge to either of the “gutters” of the cereal box piece.  These two areas need to move freely and your book will not open properly if these are glued down to your book. Let dry completely.
12. Add decorative paper to your book cover, back and spine using ModPodge.  Let dry. If the paper pieces are hanging over a bit, you can use an emery board to “sand” off the excess edge or use an sharp craft blade if you do not want the “shabby” look than the sanding will provide.
13. Decorate book with embellishments and you have a chipboard book that you are ready to fill with memories.

 

NOTE:  If you do not have chipboard, you can use layers of cereal boxes to create chipboard to use for your books.  Simply sand pictured sides of cereal box.  Cut to desired size and then glue pictured sides together.  This creates a piece that is thick enough for each page. 

Monday, February 14, 2011

PENCUT Compact Scissors now available!

THEY ARE FINALLY HERE!!! YEAH!!!



* * * PENCUT * * *

NEW compact scissors

Wonderful compact way to carry scissors with you where ever you go!
Perfect for crafters, students, seamstresses, businessmen, etc.
Where ever you might need a pair of scissors...you now have a compact way to keep a pair...
*  in the glove compartment of your car
*  in your briefcase
*   in your backpack
*   in your pocket (looks just like a pen when cap is on)
*  in your craft bag
ETC ETC ETC


Special Features:
1.  Cap with clip: Ensures safety and protects blades while storing/traveling
2.  Sliding Knobs: Softie® Handles will appear/disappear by sliding the knobs up/down
3.  Handle Stoppers:  Adjustable for right OR left handed with a simple switch of the stoppers
4.  Softie® Handles: Conveniently store away into the scissor body
5.04" total length.  2" blades



AND JUST LOOK HOW EASY THEY ARE TO USE...


* Move sliding knobs down to the bottom of the handle(s)
*  Softie® Handles will appear as you slide the knobs down
* Insert thumb and finger into the  Softie® Handles and cut!
THAT SIMPLE AND FAST!


Designed for Right OR Left handed individuals


Scissors come packaged as a RIGHT handed pair...but it is so simple to transform them into a "lefty" pair...
* Remove stoppers and click them into place on the opposite sides of the scissor handles.
TA DA...Left handed scissors in less than 15 second!



PENCUT scissors come in 3 different colors:
BLACK   PINK   GREEN







  



PAYMENT:  $10.00/pair + $2.00 shipping.  

Instructions for ordering:  If you would like a pair of the PenCut scissors, please email me at utahscraftychick@yahoo.com with your request & color preference.  I will then send you an invoice through Paypal.  I will ship them as soon as payment is received.  If you live local, you are welcome to pick them up in person. 



Please ask any questions BEFORE buying.  First come, first serve! :)